Tutorials

Verifying Defects
PTC Integrity
|
7 Views
|
Intermediate Level
|
Sheilah Fournier
In this tutorial you will learn to create a Test Session from an existing Defect.

Resolving Defects
PTC Integrity
|
7 Views
|
Intermediate Level
|
Sheilah Fournier
In this tutorial you will learn how to use Defects to resolve failed Test Cases.

Updating Test Objectives
PTC Integrity
|
0 Views
|
Intermediate Level
|
Sheilah Fournier
In this tutorial you will learn how to link Test Objectives to Test Suites and Test Cases.

Defining Test Objectives
PTC Integrity
|
0 Views
|
Intermediate Level
|
Sheilah Fournier
In this tutorial you will learn how to create and link Test Objectives to a Test Plan

Creating Test Cases
PTC Integrity
|
7 Views
|
Intermediate Level
|
Sheilah Fournier
In this tutorial you will learn how to create Test Cases within an Integrity Test Suite Document.

Component of a sub-assembly with different constraint sets in one overall assembly
PTC Creo Parametric
|
206 Views
|
Intermediate Level
|
Bin Chen
In this tutorial you will learn how to set the component with different constraint sets -Apply the same sub-assembly with different status in one overall assembly -Simple Rep cannot be satisfied because the quantity of components will be added -Family table cannot be satisfied because the name of sub-assembly will be changed ... (Show more)(Show less)

Creating Plug and Slot Welds in Creo Parametric
PTC Creo Parametric
|
799 Views
|
Introductory Level
|
Matt Stirland
In this demonstration, we fill a hole and a slot in Creo Parametric by creating a Plug weld and a Slot weld.

Removing Webs and Creating Wrap models from Imported Point Cloud Data
PTC Creo Parametric
|
537 Views
|
Intermediate Level
|
Eric Backos
This demonstration shows you how to import point cloud data and create a Wrap Model. Next, it shows how to remove webs from the handle area of the Part Model. Then, it shows the Push Shallow and Shoot Through functionality. Finally, it will show how to make the Wrap Model. ... (Show more)(Show less)

Creating a V Groove Weld in Creo Parametric
PTC Creo Parametric
|
548 Views
|
Introductory Level
|
Matt Stirland
In this demonstration, we will join two plates together in Creo Parametric by creating a V Groove Weld between them.

Understanding Save, Upload, and Check In
PTC Creo Parametric
|
465 Views
|
Introductory Level
|
William Gruss
John was unable to locate a dowel pin that he needs for his design. John will create a new Creo Parametric part to model the dowel pin and he will check the design into the Standard Parts library. In this exercise, you take the role of John Evans as he designs a dowel pin and shares the design in the Standard Parts library. As part of this exercise, you will open a standalone Web browser and, as the part is saved, uploaded, and checked into Windchill, compare the standalone Web browser information with the information displayed in the Creo Parametric embedded Web browser. ... (Show more)(Show less)

Checking Out and Modifying CAD Documents
PTC Windchill ProjectLink
|
255 Views
|
Intermediate Level
|
William Gruss
John needs to increase the pitch of the angled surface on the tip of the chuck 510 part. To accomplish this he needs to check out the part and alter the model geometry. In this exercise, you take the role of John Evans as he checks out the chuck 510 CAD document, modifies the model, and checks the CAD document back into the Windchill environment. ... (Show more)(Show less)

BOMs and reports in Advanced Framework Extension
PTC Creo
|
661 Views
|
Introductory Level
|
Jillian Wooldridge
This short demonstration shows how to create a Bill of Materials (BOM), a stock length table, and optimized cut lists using Creo’s Advanced Framework Extension (AFX). It shows how to modify table layout, format, and information included. Additionally, the demonstration shows how to use item number notes to correspond parts in a drawing to a BOM table. ... (Show more)(Show less)

Introduction to Welding in Creo Parametric
PTC Creo Parametric
|
740 Views
|
Introductory Level
|
Matt Stirland
In this demonstration we will explore the Welding application in Creo Parametric including weld rod material and parameters, weld processes and weld features. Finally we will create a Fillet weld.

Applying Manikin Reach Constraints
PTC Creo Parametric
|
359 Views
|
Introductory Level
|
Jay Aurila
This video shows the Reach Envelope and Reach functions within Creo Parametric Manikin Extension.

Learning Exchange